← Guide

Effects that use the frames around a frame

This page lists the effects of version 1.2 that look at the frames before and after the one being shown: trails and smears, a camera-style motion blur, and the repair effects for dust, flicker and colors that drift. They sit in the effects library (Toolbox > Effects) in the folders named below. Put one on a clip and change its settings in the Inspector.

A few things hold for all of them:

  • They read the same clip at its own frame steps. Trimming, speed changes, reverse and freeze frames are respected: on a clip at double speed the "previous frame" is two source frames back. At the very start of the footage the first frame repeats instead of showing nothing, and next to a trimmed edge they use the frames you trimmed away.

  • They look at no more than a few frames (at most six in all, however many are stacked), so playback stays smooth. If a neighbouring frame cannot be shown in time, the effect uses the nearest frame that is there.

  • A paused frame, playback and an export show the same picture for the same frame. Nothing builds up from one frame to the next.

  • Effects above one of these in the Inspector are applied to the neighbouring frames too, so a color correction before Deflicker counts in the brightness it measures.

  • On an adjustment clip, and inside a Compositing page clip, they see the current frame only (the picture below is not drawn again at other frames), so they change nothing there; put them on the clip itself. Patch Replacer works anywhere.

Temporal

  • Motion Trails. Leaves a fading trail of the earlier frames behind everything that moves. Trails is how many frames are used, Frame Spacing how far apart they are, Fade how quickly the older ones fade away, Trail Opacity how strong the trail is. Lighten shows the brightest of the frames, which suits light objects on a dark background; Average blends them. Nothing is drawn in front of what moves.

  • Smear. Averages the frame with the frames around it, for a soft smear along every movement. Length is how many frames on each side, Direction limits it to the frames Behind or Ahead, Falloff makes the farther frames count less and Amount mixes the smear with the plain picture.

  • Motion Blur. Measures how the picture moves from the previous frame to this one and on to the next, and blurs along that movement, the way a camera shutter does. Shutter Angle is how long the shutter is open (180 degrees is the usual look, 360 degrees blurs over a whole frame) and Quality is the number of samples along the blur. It works well for objects that move steadily; where the picture changes without moving (a flicker, a fade) nothing is blurred. The movement is found by comparing small blocks of the picture, so very fast or very small motion, and things that appear from behind other things, can come out smeared or left sharp.

Revival

  • Frame Replacer. Replaces a damaged frame with the Previous Frame, the Next Frame or a Mix of Both. Replace is the share that is replaced: leave it at 100 and cut the clip so that only the bad frame has the effect, or keyframe Replace from 0 up to 100 and back at the bad frame.

  • Deflicker. Evens out brightness that jumps from frame to frame by pulling each frame toward the average of the frames around it. Time Window is how many frames on each side are averaged (a longer window flattens slower flicker), Strength how much of the correction is applied, Limit the most the brightness may be changed. Correct Colour Too corrects each color channel on its own instead of only the brightness.

  • Automatic Dirt Removal. Removes dust and hairs that show in one frame only. A spot counts as dirt when it differs clearly from the frames before and after (Dirt Contrast) while those two frames look alike (Motion Tolerance, so things that really move are kept). Grow adds a margin around what is found, Strength mixes the repair with the original. With Time Window 2 five frames are used, which also removes dust that stays for two frames. Something thinner than the distance it moves in one frame looks like dust to this effect: raise Dirt Contrast, or use Dust Buster on the part of the picture that has the dust.

  • Dust Buster. The same repair, but only inside a region you place: Region Shape, Center X / Y, Width, Height and Feather (the repair fades in from the edge). Repair can be Detected Dirt, or Whole Region, which replaces everything inside the region with what the frames around show there. There is no on-screen handle for the region yet; type its position and size.

  • Patch Replacer. Covers a blemish with a patch copied from another place in the same picture. Source X / Y is where the patch comes from, Target X / Y where it goes (pixels from the middle of the picture), Width, Height, Patch Shape, Feather and Blend. It uses only the current frame.

Color

  • Color Stabilizer. Holds exposure and white balance steady by matching every frame to a Reference Frame (a frame number counted from the start of the clip). Match can be Exposure and White Balance, Exposure only, or White Balance only (the brightness of each frame is kept). Region X / Y / Width / Height (percent of the picture) choose the part of the picture the colors are measured in, so a patch of sky or a grey wall can stand for the whole scene; keep it off moving people. Strength and Limit work as in Deflicker. The reference frame is read for every frame, so choose a frame inside the clip.

See also Sharpen, repair, damage and paint effects for the other effects in the Revival folder, and Steady a shaky clip.